Extension Logo
Extension Logo
University of Minnesota Extension
extension.umn.edu

Moisture in basements: causes and solutions

This page briefly describes moisture sources, moisture movement mechanisms and typical basement moisture problems. Then, a step-by-step process for addressing each problem is presented along with several detailed approaches to solving the problem.

A problem that can damage your health and home

Moisture problems in existing basements are very common, but often are not understood or properly treated. In a basement that is seldom used and separate from the living spaces above, this may not present a great problem. However, most basements in Minnesota are connected to the rest of the house through ductwork or other openings. In addition, basements are increasingly used as finished living and bedroom spaces. In these cases, moisture problems are not only annoying and uncomfortable, but can lead to significant health problems. Molds and mildew can grow in damp carpets and beneath wall coverings. Finishing a basement without first dealing with the moisture problems can result in making health conditions worse and lead to significant damage as well. Basement water problems are solvable, but there is a cost to doing it right.

Understanding the problem

To correct basement moisture problems, it's necessary to understand where the water is coming from and what mechanisms permit it to enter the basement. There are just three sources of moisture:

  1. Liquid water from rain or ground-water.
  2. Interior moisture sources such as humidifiers, unvented clothes dryers, bathrooms and cooking, as well as the moisture in concrete after construction.
  3. Exterior humid air that enters the basement and condenses on cooler surfaces.

Moisture is transferred from the outside of the building to the basement interior by four mechanisms:

  1. Liquid water flow.
  2. Capillary suction.
  3. Vapor diffusion.
  4. Air movement.

Sometimes problems are traced to poor construction with cracking, settling foundations. In many cases, however, houses and basements can be structurally sound but are often not properly built to handle water drainage. Failure to slope the ground surface away from the foundation or lack of a good gutter and downspout system is common. Missing or nonfunctioning subsurface drainage systems are also found relatively frequently. These problems can all be addressed and corrected if a systematic approach is used.

This page briefly describes moisture sources, moisture movement mechanisms and typical basement moisture problems. Then, a step-by-step process for addressing each problem is presented along with several detailed approaches to solving the problem.

Symptoms

  • Water trickling out of walls.
  • Standing water on floor.
  • Saturated base of concrete block walls; a ring of dampness.
  • Damp, humid air.
  • Condensation on cold walls and floor in summer.
  • Odor, mold and mildew.
  • Deterioration of carpet or wood.
  • Rot and decay of wood headers, joists, sill plates and columns.
  • Staining and blistering of wall covering.
  • Efflorescence, spalling of concrete or masonry.

Basement moisture sources

Rain and groundwater

Rain and groundwater

In a 1-inch rain, 1,250 gallons of water fall on the roof of a 2,000-square-foot house. Without proper grading, gutters and downspouts, some of this water flows into the basement. The below-grade water table can also rise due to flooding or seasonal site conditions. This is why drain tile systems are recommended around basement walls even in sandy or gravel soils.

Interior moisture sources in basement.
Interior moisture sources

Interior moisture sources

Moisture is generated inside of basements from people and their activities. Common sources are humidifiers, unvented clothes dryers, showering and cooking. When basements are finished, these activities increase.

Another source that can be thought of as internal is the moisture contained in new concrete after construction. In a typical house, this can amount to 0.2 gallons per square foot of wall, and 0.1 gallons per square foot of floor. It may take many months or even years for a new house to come into equilibrium with its environment.

Ventilation with humid outside air.
Ventilation with humid outside air

Ventilation with humid outside air

In the summertime, basement windows may be opened for fresh air. If the outside air is warm and humid, it will condense on the cool basement wall and floor surfaces. Many homeowners see this moisture and believe they are experiencing basement wall leakage, when in fact the accumulated moisture is from condensation.

Moisture movement mechanisms

Moisture movement mechanisms - capillary suction.
Capillary suction

Capillary suction

Capillary suction moves moisture through porous materials. The water can be drawn upward through small pores in the concrete footing and slab and laterally through walls. This effect creates the ring of dampness seen at the base of many basement walls. This is very common at cold joints. Water can rise by capillary draw significantly as shown below:

Soil type and amount of capillary rise:

  • Gravel - Less than a few inches.
  • Sand - 1 to 8 feet.
  • Silt - 12 to 16 feet.
  • Clay - 12 to 20 feet.
Moisture movement mechanisms - Air leakage through walls and floor.
Air leakage through walls and floor

Air leakage through walls and floor

In most houses, a stack effect is created because warm air rises. This induces a negative pressure on the basement and draws moist air in through any cracks or openings in the foundation including open sump pits. For this reason, sumps should have an airtight cover. With a concrete block foundation, moist air is drawn through the block cores, especially if they are left open at the top course.

Moisture movement mechanisms - Vapor diffusion through foundation walls.
Vapor diffusion through foundation walls

Vapor diffusion through foundation walls

Vapor diffusion is the movement of moisture in the vapor state through a material. It's dependent on the permeability of the material and the driving force of vapor pressure differential. In a basement, vapor can diffuse from the wetter ground through concrete walls and floors toward the dryer basement interior. Vapor retarders such as foundation waterproofing and polyethylene slow down this process.

Typical causes of basement moisture problems

Causes of moisture problems - inadequate grading.
Inadequate grading

Inadequate grading

PROBLEM: If the ground around a foundation is level or slopes toward the house, water is directed into the basement. The soil next to the house is often backfilled without proper compaction and later settles. This is especially true under stoops where water can collect next to the basement wall.

SOLUTION: Place earth around the house so that it slopes away from the foundation wall a minimum of 1 inch per foot for at least 6 feet.

Defective or missing gutters and downspouts contribute to basement moisture.
Defective or missing gutters and downspouts

Defective or missing gutters and downspouts

PROBLEM: Missing gutters and downspouts cause rainwater to be directed toward the foundation perimeter. A downspout without an extender or splash block is worse than no downspout at all. It is depositing the huge volume of rainwater from the roof in a single concentrated location near the basement.

SOLUTION: Place a minimum of one downspout per 50 linear feet of roof eave. Extensions should discharge water at least 4 feet beyond the wall. Sloped concrete sidewalks around basements are very effective in directing rain runoff.

Improperly designed window wells cause water to flow toward basement.
Improperly designed window wells

Improperly designed window wells

PROBLEM: Window wells are like a drain right next to the basement wall. Often they are improperly built so that any water is directed toward, rather than away from the foundation.

SOLUTION: Window wells should be filled from the footing to the window sill with 3/8- to 3/4-inch coarse aggregate. A supplemental drain tile extension should extend from the footing to the base of the window well.

Ineffective drain tile and sump pit
Ineffective drain tile and sump pit

Ineffective drain tile and sump pit

PROBLEM: Many existing houses simply have no subsurface drainage system. This comes from a time when basements were not used as habitable space. In other cases, the systems don't work for a variety of reasons, such as collapse of the pipe, clogging of the pipe with silt and/or tree roots or a broken connection to the sump. The sump pit usually contains a pump designed to lift the water to the ground surface outside the foundation wall. This pump can fail.

SOLUTION: See approaches 2 through 5 that follow.

Improper drainage with underslab ducts
Improper drainage with underslab ducts

Improper drainage with underslab ducts

PROBLEM: If heating ducts are installed beneath a basement floor slab, the drainage system may be inappropriately left at a level higher than the duct. In effect, the duct becomes the drainage system. With standing water within the heating duct, there are potentially serious health consequences from mold contamination.

SOLUTION: Heating ducts placed beneath the basement floor must be insulated, watertight and sloped to collection points for drainage and cleaning. A drain tile and coarse aggregate can be placed under the ductwork.

Structural cracks let water in basement.
Structural cracks

Structural cracks

PROBLEM: Concrete and concrete block foundations usually develop some cracks. They can be severe if floor joists are not properly connected to the foundation wall, thus permitting the wall to move. Also, soil settling causes cracking. Places where walls meet rigid structures like the fireplace often crack as well. Usually, drainage removes the water from cracks, but repair may be necessary.

SOLUTION: Proper footing design and proper connection between the foundation wall and the structure above are required (e.g. anchor bolts or straps at the sill plate and floor joists nailed to the sill plate).

An overview of solutions to basement moisture problems

The best way to approach any building problem is to first do the things that are easy and low-cost. Then proceed in a logical order doing the next least costly technique with the most positive likely result. With moisture problems, the best approach is almost always to remove or control the source of the moisture, not to try to stop it at the last line of defense.

  1. First, the simplest and least costly techniques are to remove excessive internal moisture sources in the basement (humidifiers, cooking) and ventilate other sources (clothes dryer, bathroom).
  2. Second, if condensation in the summer is the problem, do not ventilate the basement directly with warm, humid air. Ventilation through an air conditioning system or with a desiccant-type heat exchanger is recommended.

Dehumidification is not a permanent solution

Dehumidification can be used as a means of reducing the symptoms of humidity and odor in a basement, but it is not a permanent or complete solution. In fact, if a dehumidifier is used in a basement with moisture problems, it may cause greater damage. By drying out the basement air, moisture is drawn into the basement more rapidly causing efflorescence and spalling of concrete and further damage to interior finishes.

Interior membrane or coating is a temporary solution

It is appealing to solve a basement moisture problem with a membrane or coating on the inside. It's less expensive than a drainage system and seems to work for a time in some cases. The water is still there, however, and eventually, these systems deteriorate or simply move the water to another pathway into the basement.

Recommended approach

Evaluate gutters, downspouts and surface grading: The recommended approach after removing interior moisture sources is to evaluate the gutters, downspouts and surface grading around the house. These should be corrected first and may solve the problem.

Interior or exterior drainage system: Then, if a moisture problem persists, proceed with an interior or exterior drainage system. All of these techniques are described below. If your goal is to finish a basement that has water problems, it is recommended to first deal with the water problem.

Sub-slab depressurization system: An active sub-slab depressurization system including a washed-rock layer below the slab is recommended. This draws moist air from beneath the slab and may help to reduce the amount of moisture vapor that enters the home through openings in the slab. It also assists in controlling radon and other soil gases. Sumps and other open connections to the soil outside the foundation and below the slab should be blocked and sealed.

Step-by-step process

  1. Control interior moisture sources.
  2. If summertime, don't ventilate with outside air.
  3. Correct grading, gutter and downspout system.
  4. Provide an interior or exterior drainage system.

Notes

  • A dehumidifier can help reduce the symptoms of humidity and odor but doesn't solve the problem.
  • A membrane or coating on the interior without providing drainage generally won't solve the problem in the long term.
  • Walls must be dry before insulating. Slabs must be warm and dry before carpeting.
 | 

John Carmody; Brent Anderson; and Richard Stone, Extension educator

Reviewed in 2018

Page survey

© 2024 Regents of the University of Minnesota. All rights reserved. The University of Minnesota is an equal opportunity educator and employer.